-800x800.jpg "Lectrosonics - M2T Duet System IEM/IFB Transmitter")
Features
- IEM (Wireless Monitor) with digital RF transmission
- 2 independent stereo audio transmissions per 1/2 RV enclosure
- USB port for firmware updates
- Fully Dante™ compatible
- IR (infrared) port for fast setup
- Up to 50 mW per Rf carrier
- All metal housing
- Compatible with Wireless Designer™ Software
The M2T half-rack transmitter houses two stereo transmitters to provide two stereo audio channels, and for up to four mono audio channels in a single rack space. The audio inputs can be individually configured to be analog or Dante compatible. The analog input connectors are full-size XLR/TRS combo types for balanced line-level analog signals while the input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. A Dante™ Ultimo™ interface via dual RJ45 connectors accepts Dante networked audio inputs and can daisy chain the digital stream to additional units via CAT6 cables. An additional RJ45 jack provides an Ethernet connection for programming and control via Wireless Designer™ software and a USB jack on the front panel allows for firmware updates. The transmitter features a full color, backlit LCD for high visibility in any environment, while the chassis is all-metal and can be racked singly or in pairs using included rack mount hardware.
Included Accessories
- 21926 Cable USB
- 25990 Bracket Rear Tie M2T/M4T
- 25991 Bracket Front Tie M2T/M4T
- 27076 Rack Flange Bracket
- 27082 Rack Handle RMP2T
- 4 - 28885 SCR10 Cap Screw
- 4 - 35664 Rubber Foot (Large)
- 35800 Hex L Key Wrench
- 35959 Hole Plug
- 2 - A500RA20 Antenna
- DCR15/4AU DC Power Supply
- Instruction Manual
| Specifications | |
| Capacity | Specifications RF Power Output: • Two carriers; two audio channels each • M2T, M2T/E02: Power adjustable on each carrier to 10, 25 or 50 mW M2T/E06: Power adjustable on each carrier to 20, 50 or 100 mW EIRP Antenna Output: 2 x BNC sockets Operating Frequencies: M2T 470.100 – 607.975 MHz Operating Temperature Range: Celsius: -20° - 40° Farenheit: -5° - 104° Frequency Selection Steps: 25 kHz Frequency Stability: ± 0.002% Modulation: 8 PSK Emission Designator: 200KG7E Spurious Radiation: Compliant with ETSI EN 300 422-1 Equivalent input Noise: –128 dBV Latency: (overall system) Digital Source: 1.0 ms plus Dante network (on Dante unit) Analog Source: <1.4 ms Audio Frequency Response: 10 Hz – 11.5 kHz, -1 dB Audio Input: -10 dBV or +4 dBu settings w/ ±5 dB trim Audio Input Jack: 4 x combo XLR/TRS connectors Input impedance: Line: 2k Ohm Dante Connection: 2 x RJ45, 4 audio RX channels, internally routable Ethernet Connection:RJ45 USB Connection: Micro USB on front panel for firmware updates IRDA: IR transceiver for sync of receivers Headphone jack 3.5 mm stereo jack Power Requirements: 9-18 VDC Power Consumption: 11 Watts Weight: 2.2 lbs (997.903 grams) Dimensions: Height: 1.750 in. / 44.45 mm Width: 8.375 in. / 212.7 mm Depth: 7.750 in. / 196.8 mm9 |
Related Products
Lectrosonics - MTCR Timecode Recorder
FeaturesProfessional quality digital audio recordings in Broadcast Wave FormatUltra compact size for..
$926.00
Lectrosonics - M2Ra Digital IFB/IEM Receiver
FeaturesIEM (Wireless Monitor) receiver with digital RFIR (infrared) port for fast setupHigh resolut..
$1,499.00